VXLAN Networks

This guide describes how to enable Network isolation provided through the VXLAN encapsulation protocol. This driver will create a bridge for each OpenNebula Virtual Network and attach a VXLAN tagged network interface to the bridge.

The VXLAN ID will be the same for every interface in a given network, calculated automatically by OpenNebula. It may also be forced by setting the VLAN_ID attribute in the Virtual Network template.

Additionally, each VXLAN has an associated multicast address to encapsulate L2 broadcast and multicast traffic. By default, the address assigned will belong to the 239.0.0.0/8 range as defined by RFC 2365 (Administratively Scoped IP Multicast). The multicast address is obtained by adding the value of the attribute VLAN_ID to 239.0.0.0/8 base address.

Considerations & Limitations

This driver works with the default UDP server port 8472.

VXLAN traffic is forwarded to a physical device; this device can be set (optionally) to be a VLAN tagged interface, but in that case you must make sure that the tagged interface is manually created first in all the Hosts.

Important

The network interface that will act as the physical device must have an IP.

Limited Count of VXLANs on Host

Each VXLAN is associated with one multicast group. There is a limit on how many multicast groups can be a physical Host member of at the same time, which also means how many different VXLANs can be used on a physical Host concurrently. The default value is 20 and can be changed via sysctl through the kernel runtime parameter net.ipv4.igmp_max_memberships.

For permanent change to e.g. 150, place the following settings inside the /etc/sysctl.conf:

net.ipv4.igmp_max_memberships=150

and reload the configuration

sysctl -p

OpenNebula Configuration

It is possible specify the start VXLAN ID by configuring /etc/one/oned.conf:

# VXLAN_IDS: Automatic VXLAN Network ID (VNI) assigment. This is used
# for vxlan networks.
#     start: First VNI to use

VXLAN_IDS = [
    START = "2"
]

The following configuration parameters can be adjusted in /var/lib/one/remotes/etc/vnm/OpenNebulaNetwork.conf:

Parameter

Description

:vxlan_mc

Base multicast address for each VLAN. The multicas address is vxlan_mc + vlan_id

:vxlan_ttl

Time To Live (TTL) should be > 1 in routed multicast networks (IGMP)

:validate_vlan_id

Set to true to check that no other VLANs are connected to the bridge

:keep_empty_bridge

Set to true to preserve bridges with no virtual interfaces left.

:ip_bridge_conf

(Hash) Options passed to ip cmd. on bridge create (ip link add <bridge> type bridge ...)

:ip_link_conf

(Hash) Options passed to ip cmd. on VLAN interface create (ip link add)

Note

Remember to run onehost sync -f to synchonize the changes to all the nodes.

Example:

# Following options will be added when creating bridge. For example:
#
#     ip link add name <bridge name> type bridge stp_state 1
#
# :ip_bridge_conf:
#     :stp_state: on


# These options will be added to the ip link add command. For example:
#
#     sudo ip link add lxcbr0.260  type vxlan id 260 group 239.0.101.4 \
#       ttl 16 dev lxcbr0 udp6zerocsumrx  tos 3
#
:ip_link_conf:
    :udp6zerocsumrx:
    :tos: 3

Defining a VXLAN Network

To create a VXLAN network, include the following information in the template:

Attribute

Value

Mandatory

VN_MAD

Set vxlan

YES

PHYDEV

Name of the physical network device that will be attached to the bridge.

YES

BRIDGE

Name of the linux bridge, defaults to onebr<net_id> or onebr.<vlan_id>

NO

VLAN_ID

The VXLAN ID, will be generated if not defined and AUTOMATIC_VLAN_ID=YES

YES (unless AUTOMATIC_VLAN_ID)

AUTOMATIC_VLAN_ID

Mandatory and must be set to YES if VLAN_ID hasn’t been defined

YES (unless VLAN_ID)

MTU

The MTU for the tagged interface and bridge

NO

VXLAN_MODE

Multicast protocol for multi destination BUM traffic:evpn or multicast

NO

VXLAN_TEP

Tunnel endpoint communication type (only for evpn): dev or local_ip

NO

VXLAN_MC

Base multicast address for each VLAN. The MC address is :vxlan_mc + :vlan_id

NO

IP_LINK_CONF

Options passed to ip cmd. on operations specific to this Virtual Network. Syntax: IP_LINK_CONF="option1=value1,option2=,option3=value3,..."

NO

Note

VXLAN_MODE, VXLAN_TEP and VXLAN_MC can be defined system-wide in /var/lib/one/remotes/etc/vnm/OpenNebulaNetwork.conf. To use per network configuration you may need the IP_LINK_CONF attribute.

For example, you can define a VXLAN Network with the following template:

NAME    = "private3"
VN_MAD  = "vxlan"
PHYDEV  = "eth0"
VLAN_ID = 50            # Optional
BRIDGE  = "vxlan50"     # Optional

In this example, the driver will check for the existence of the vxlan50 bridge. If it doesn’t exist it will be created. eth0 will be tagged (eth0.50) and attached to vxlan50 (unless it’s already attached). Note that eth0 can be a 802.1Q tagged interface, if you want to isolate the VXLAN traffic by 802.1Q VLANs.

Using VXLAN with BGP EVPN

By default, VXLAN relies on multicast to discover tunnel endpoints; alternatively you can use MP-BGP EVPN for the control plane and hence increase the scalability of your network. This section describes the main configuration steps to deploy such a setup.

Configuring the Hypervisors

The hypervisor needs to run a BGP EVPN capable routing software like FFRouting (FRR). Its main purpose is to send BGP updates with the MAC address and IP (optional) for each VXLAN tunnel endpoint (i.e. the VM interfaces in the VXLAN network) running in the Host. The updates need to be distributed to all other hypervisors in the cloud to achieve full route reachability. This second step is usually performed by one or more BGP route reflectors.

As an example, consider two hypervisors 10.4.4.11 and 10.4.4.12, and a route reflector at 10.4.4.13. The FRR configuration file for the hypervisors could be (to be announced to all VXLAN networks):

router bgp 7675
 bgp router-id 10.4.4.11
 no bgp default ipv4-unicast
 neighbor 10.4.4.13 remote-as 7675
 neighbor 10.4.4.13  capability extended-nexthop
 address-family l2vpn evpn
  neighbor 10.4.4.13 activate
  advertise-all-vni
 exit-address-family
exit

And the reflector for our AS 7675 and hypervisors in 10.4.4.0/24:

router bgp 7675
  bgp router-id 10.4.4.13
  bgp cluster-id 10.4.4.13
  no bgp default ipv4-unicast
  neighbor kvm_hosts peer-group
  neighbor kvm_hosts remote-as 7675
  neighbor kvm_hosts capability extended-nexthop
  neighbor kvm_hosts update-source 10.4.4.13
  bgp listen range 10.4.4.0/24 peer-group kvm_hosts
  address-family l2vpn evpn
   neighbor fabric activate
   neighbor fabric route-reflector-client
  exit-address-family
exit

Note that this a simple scenario using the same configuration for all the VNIs. Once the routing software is configured you should see the updates in each hypervisor for the VMs running in it, for example:

10.4.4.11# show bgp evpn route
   Network          Next Hop            Metric LocPrf Weight Path
Route Distinguisher: 10.4.4.11:2
*> [2]:[0]:[0]:[48]:[02:00:0a:03:03:c9]
                    10.4.4.11                          32768 i
*> [3]:[0]:[32]:[10.4.4.11]
                   10.4.4.11                           32768 i
Route Distinguisher: 10.4.4.12:2
*>i[2]:[0]:[0]:[48]:[02:00:0a:03:03:c8]
                   10.4.4.12                0    100      0 i
*>i[3]:[0]:[32]:[10.4.4.12]
                   10.4.4.12                0    100      0 i

Configuring OpenNebula

You need to update the /var/lib/one/remotes/etc/vnm/OpenNebulaNetwork.conf file by:

  1. Setting BGP EVPN as the control plane for your BUM traffic, :vxlan_mode.

  2. Selecting the hypervisor that is going to send the traffic to the VTEP. This can be either dev, to forward the traffic through the PHY_DEV interface defined in the Virtual Network template, or local_ip to route the traffic using the first IP configured in PHY_DEV.

  3. Finally, you may want to add the nolearning option to the VXLAN link.

# Multicast protocol for multi destination BUM traffic. Options:
#   - multicast, for IP multicast
#   - evpn, for BGP EVPN control plane
:vxlan_mode: evpn

# Tunnel endpoint communication type. Only for evpn vxlan_mode.
#   - dev, tunnel endpoint communication is sent to PHYDEV
#   - local_ip, first ip addr of PHYDEV is used as address for the communiation
:vxlan_tep: local_ip

# Additional ip link options, uncomment the following to disable learning for
# EVPN mode
:ip_link_conf:
    :nolearning:

After updating the configuration file on the Front-end, don’t forget to execute onehost sync -f to distribute the changes on the hypervisor nodes.

Note

It is not recommended to set :nolearing: in :ip_link_conf: system-wide attribute in /var/lib/one/remotes/etc/vnm/OpenNebulaNetwork.conf because that doesn’t allow the coexistence of VLAN and VXLAN with BGP EVPN Virtual Networks on Hosts. For VXLAN with BGP EVPN, set IP_LINK_CONF="nolearning=" attribute in the Virtual Network definition instead.