Federation Configuration

This section will explain how to configure two (or more) OpenNebula Zones to work as federation master and slave. The process described here can be applied to new installations or existing OpenNebula instances.

OpenNebula master Zone server replicates database changes on slaves using a federated log. The log contains the SQL commands which should be applied in all Zones.

In this document, each configuration step starts with Master or Slave to indicate the server where the step must be performed.


Master and slave servers need to talk to each other through their XML-RPC API. You may need to update the LISTEN_ADDRESS, and or PORT in /etc/one/oned.conf, or any firewall rule blocking this communication. Note that by default this traffic is not secure, so if you are using public links you need to secure the communication.


The federation can be set-up with MySQL/MariaDB or SQLite backends, but you can’t mix them across Zones. MySQL/MariaDB is recommended for production deployments.


FireEdge is a next-generation GUI, which is not fully supported in federation environments yet. Please connect only to the zone you which to operate with FireEdge directly, as it doesn’t allow to switch zones. Also take into account that the FireEdge functionality enabled in Sunstone won’t be present if you switch to a remote zone in Sunstone.

Step 1. Configure the OpenNebula Federation Master Zone

Start by picking an OpenNebula to act as master of the federation. The master OpenNebula will be responsible for updating shared information across Zones and replicating the updates to the slaves. You may start with an existing installation or with a new one (see the installation guide).


When installing a new master from scratch be sure to start it at least once to properly bootstrap the database.

  • Master: Edit the master Zone endpoint. This can be done via Sunstone, or with the onezone command. Write down this endpoint to use it later when configuring the slaves.
onezone update 0
ENDPOINT = http://<master-ip>:2633/RPC2


In the HA setup, the <master-ip> should be set to the floating IP address, see the HA installation guide for more details. In single server Zones, just use the IP of the server.

  • Master: Update /etc/one/oned.conf to change the mode to master.
    MODE    = "MASTER",
    ZONE_ID = 0
  • Master: Restart the OpenNebula.

You are now ready to add slave Zones.

Step 2. Adding a New Federation Slave Zone

  • Slave: Install OpenNebula on the slave as usual following the installation guide. Start OpenNebula at least once to bootstrap the Zone database.
  • Slave: Stop OpenNebula.
  • Master: Create a Zone for the slave, and write down the new Zone ID. This can be done via Sunstone, or with the onezone command.
vim /tmp/zone.tmpl
NAME     = slave-name
ENDPOINT = http://<slave-zone-ip>:2633/RPC2
onezone create /tmp/zone.tmpl
ID: 100
onezone list
    0 OpenNebula
  100 slave-name


In HA setups use the floating IP address for the <slave-zone-ip>; in single server Zones just use the IP of the server.

  • Master: Make a snapshot of the federated tables with the following command:
onedb backup --federated -s /var/lib/one/one.db
Sqlite database backup of federated tables stored in /var/lib/one/one.db_federated_2017-6-15_8:52:51.bck
Use 'onedb restore' to restore the DB.


This example shows how to make a database snapshot with SQLite. For MySQL/MariaDB just change the -s option with the corresponding MySQL/MariaDB options: -u <username> -p <password> -d <database_name>. For SQLite, you need to stop OpenNebula before taking the DB snapshot. This is not required for MySQL/MariaDB.

  • Master: Copy the database snapshot to the slave.
  • Master: Copy only selected files from the directory /var/lib/one/.one to the slave. This directory and its content must have oneadmin as owner. Replace only these files:
ls -1 /var/lib/one/.one
  • Slave: Update /etc/one/oned.conf to change the mode to slave, set the master’s URL and the ZONE_ID obtained when the zone was created on master:
    MODE        = "SLAVE",
    ZONE_ID     = 100,
    MASTER_ONED = "http://<master-ip>:2633/RPC2"
  • Slave: Restore the database snapshot:
onedb restore --federated -s /var/lib/one/one.db /var/lib/one/one.db_federated_2017-6-14_16:0:36.bck
Sqlite database backup restored in one.db
  • Slave: Start OpenNebula.

The Zone should be now configured and ready to use.

Step 3. Adding HA to a Federation Slave Zone (Optional)

Now you can start adding more servers to the slave Zone to provide it with HA capabilities. The procedure is the same as the one described for stand-alone Zones in the HA installation guide. In this case, the replication works in a multi-tier fashion. The master replicates a database change to one of the Zone servers. Then this server replicates the change across the Zone servers.


It is important to double check that the federation is working before adding HA servers to the Zone, as you will be updating the Zone metadata which is federated information.

Step 4. Show service information by Zone Sunstone (Optional)

To see the information of the services in the sunstone of a particular zone, it is required to do the following:

  • Adjust the :host field in /etc/one/oneflow-server.conf of the slave zone to allow listening for requests outside of


So that the oneflow-server listens for requests from anywhere, the host field can be set to

  • Update the slave zone in the master zone. Adding the ONEFLOW_ENDPOINT=http://<slave-zone-ip>:2474/ field with the public address of the slave zone with the following command onezone update <id-slave-zone>
  • restart sunstone service

Importing Existing OpenNebula Zones

There is no automatic procedure to import existing users and groups into a running federation. However, you can preserve everything else like datastores, VMs, networks…

  • Slave: Back-up details of users, groups, and VDCs you want to recreate in the federated environment.
  • Slave: Stop OpenNebula. If the Zone was running an HA cluster, stop all servers and pick one of them to add the Zone to the federation. Put this server in solo mode by setting SERVER_ID to -1 in /etc/one/oned.conf.
  • Master, Slave: Follow the procedure described in Step 2 to add a new Zone.
  • Slave: Recreate any user, group or VDC you need to preserve in the federated environment.

The Zone is now ready to use. If you want to add more HA servers, follow the standard procedure.

Updating a Federation

OpenNebula database has two different version numbers:

  • federated (shared) tables version,
  • local tables version.


To federate OpenNebula Zones, they must run the same version of the federated tables (which are pretty stable).

Upgrades to a version that does not increase the federated version can be done asynchronously in each Zone. However, an update in the shared table version requires a coordinated update of all Zones.

Administration Account Configuration

A Federation will have a unique oneadmin account. This is required to perform API calls across Zones. It’s recommended to not use this account directly in a production environment but to create an account in the ‘oneadmin’ group for each Zone administrator instead.

When additional access restrictions are needed, the Federation Administrator can create a special administrative group with total permissions for one Zone only.